Skip to product information
1 of 1

Loba EasyFinish

Loba EasyFinish

Regular price $95.99 USD
Regular price Sale price $95.99 USD
Sale Sold out
Shipping calculated at checkout.

 

Properties

  • Water-based polyurethane-acrylate formula with excellent wear resistance
  • No mixing - no pot life - no waste
  • Excellent build through high solid content
  • Easy to use, no foaming or lap marks
  • Non-yellowing
  • 90% cured after 24 hours

Processing Instruction 

  • For professional use only!
  • BEFORE USING, READ AND UNDERSTAND ALL LABEL INSTRUCTIONS AND MATERIAL SAFETY DATA SHEETS.
  • For technical advice call our Loba-Wakol Technical Service at 1-800.230.6456.
  • Recommended conditions are 55°F-80°F/40-75%rH.
  • Sand and prepare floors according to NWFA guidelines.
  • WARNING! If you scrape, sand, or remove old paint from wood floors, you may release lead dust. Follow local and/or federal requirements for lead removal. Before you start, find out how to protect yourself and others by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
  • ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE, AND DESIRED RESULTS.
  • Shake material well before use.
  • Do not thin. Do not add water.
  • Do not apply at temperatures below 55°F (13°C). Make sure material is at room temperature. Always maintain adequate ventilation during all phases of the coating and drying process.
  • Apply evenly at the recommended coverage rate. Avoid streaks, puddles, and lap marks.
  • This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol wood flooring adhesives may be found in the "Connected Systems Matrix": https://www.loba.de/us/connected-systems/

Application Tool

LOBA roller Microfiber 100-120T-barTrim padLambswoolBrushRoller

Coverage

500-600 square feet per gallon per coat.

Drying time

  • Earliest possible recoating after 2-3 hours.
  • Fully cured after 5 days.
  • If there is a delay in drying wait until you can see that the surface is completely dry.

Recommended Procedure for wood floors:

  • Prepare and prime the substrate properly, according to directions.
  • Allow the primer to dry as specified.
  • Apply Finish.
  • Allow to dry for a minimum of 2-3 hours.
  • Intermediate sanding with LOBASAND perforated pad 180 (or equivalent).
  • Apply second layer of Finish.

Recommended Procedure for cork floors:

Seal cork only after the glue has sufficiently set (refer to manufacturer’s information)
Roll on a maximum of 2 coats per day
Untreated natural cork:
  • Roll a total of three coats of finish onto the cork.
  • Apply first coat and allow to dry 2-4 hours.
  • Apply the second coat and allow to dry overnight (reduces risk of granule swelling).
  • Intermediate sanding with LOBASAND perforated pad 180 (or equivalent) to remove grain raise. Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
  • Apply final coat.
Prefinished cork
Note information given by the cork supplier. If suitable for recoating, apply one or two layers of coating after an intermediate sanding.
Renovation / recoating of old coatings
Basic cleaning with Remover. Use a rotary disk buffing machine and a LOBASAND SpecialPad green. Care product residues must be completely removed. Even small amounts of residue can adversely effect the bond of the coating. Clean with clear water (neutralize). After drying, perform a thorough intermediate sanding or preparation with LOBA 2k Contact. Apply coating in one or two layers by roller

Suitable product combinations

Suitable product combinations

Primers:
  • EasyPrime
  • 2K Intensive
Stains:
  • 2K IntensiveColor
  • Stain
    Refer to the Technical Data Sheets for the product.

Screen and Recoat

  • Clean floor, abrade with LOBASAND 180 grit perforated pad (or equivalent). Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
  • Apply finish following instructions.
  • Always prepare test areas to determine compatibility, appearance, and desired results.
  • Do NOT use on floors finished with UV cured, oxide containing, factory applied finishes.
For professional use only!

Compatibility

When this product is used in combination with other LOBA products the technical information of these products must be followed. Refer to the Technical Data Sheets. LOBA cannot guarantee the suitability of products other than LOBA.

 

View full details
Your cart
Variant Variant total Quantity Price Variant total
Loba EasyFinish
Satin4014701616923
Satin4014701616923
$95.99/ea
$0.00
$95.99/ea $0.00
Loba EasyFinish
Semi-Gloss4014701616930
Semi-Gloss4014701616930
$95.99/ea
$0.00
$95.99/ea $0.00
Loba EasyFinish
Gloss
Gloss
$95.99/ea
$0.00
$95.99/ea $0.00

View cart
0

Total items

$0.00

Product subtotal

Taxes, Discounts and shipping calculated at checkout
View cart