Old Master Wood Conditioner 1QT

This is a pre-stain, clear wood sealer that enables uniform stain application on soft woods, such as fir, pine, or hemlock. Using this product helps to avoid the appearance of uneven, blotchy staining. This VOC-compliant formula is for Ozone Transport Commission (OTC) states and the South Coast Air Quality Management District. This formula may be open for a longer amount of time before stain must be applied. See product instructions for more information.

Description
 Old Masters  Wood Conditioner is a pre-stain, clear wood sealer that enables 
uniform stain application on soft woods, such as fir, pine, or hemlock. Generally, 
softer woods accept stain in various degrees creating an uneven appearance; Wood 
Conditioner helps to eliminate this variance. This product can be applied under 
oil- or water-based stains. Allow Wood Conditioner to dry for a minimum 24 hours 
before applying water-based stains. Ideal for use on soft woods which are being 
stained with or adjacent to hardwoods.
 Surface Preparation
 All surfaces must be clean, dry, and free from dirt, wax, or grease. If persistent wax 
exists, remove with fine steel wool saturated with paint thinner or alcohol. This 
product does not take the place of sanding sealer. It is a pre-stain treatment only.
 New Wood: Sand the wood thoroughly with medium grit sandpaper and progress 
to fine grit sandpaper. Always sand in the direction of the wood grain. Sand smooth 
and remove all dust.
 Previously Finished Surfaces: Strip the surface completely down to bare wood with 
paint or varnish remover, making sure all previous finishes are removed. Surface 
must be sanded smooth. Remove all dust.
 Note: DO NOT use a tack rag to remove dust, as it may leave a residue that will 
interfere with adhesion.
 WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS 
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN 
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID 
EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Clean up carefully 
with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and 
your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log 
on to www.epa.gov/lead
 Application
 Stir product thoroughly with a circular, lifting motion to disperse contents evenly.
 1. Apply with a polyester or nylon brush. Ensure entire surface has been coated.
 2. Allow Wood Conditioner to penetrate the surface for 5 to 15 minutes. Remove 
excess by wiping with a clean rag. Do not leave a surface film; work in a small area 
so the product cannot set up.
 3. Apply stain over Wood Conditioner after 8 hours. If stain is applied before 8 
hours, a darker color may result with less uniformity control.
 Note: Color depth may vary according to type of wood, stain and application 
technique. To ensure that your finished color is accurate, we highly recommend you 
test your technique, wood stain and wood type before you start your project.
 Thinning
 Do not thin. Use as packaged.
 Product Codes
 51104
 Quart

Coverage
 Approximately 400 to 500 square feet per gallon depending upon method of 
application, type, and porosity of wood.
 Dry Time
 Wood Conditioner will dry in approximately 8 hours. Allow Wood Conditioner to 
dry for a minimum 24 hours before applying water-based stains.
 Clean Up
 Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended 
for cleanup. The use of paint thinners or mineral spirits may violate VOC 
compliancy in your area. Check with your local government agencies to ensure 
proper compliancy.
 DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this 
product may spontaneously catch fire if improperly discarded. No ignition source is 
required for these wastes to start on fire by themselves. Immediately place rags, steel wool, 
sanding residue, and other wastes used or soaked with this product in a sealed, water-filled 
metal container. Dispose of in accordance with local fire regulations.
 Limited Warranty
 Since Old Masters does not control the application of its products, nor is the 
condition of the surface to which they are applied, a Limited Warranty is provided. If 
the products do not perform as specified, for whatever reason, Old Masters liability 
will under no circumstances exceed the replacement of the product.  
Technical Data
 Product Information
 Solids by Volume 76.8%
 Solids by Weight 78.4%
 Weight per Gallon 7.7 lbs
 Vehicle Oil
 Viscosity at 77°F 15 to 18 secs. 
#2 Zahn
 Flash Point 101°F Tag 
Closed Cup
 Recommended 
Thinner
 Do not thin.
 Used as packaged.
 VOCs 100 g/L
 Coverage
 Theoretical Coverage 
@Mil DFT 400 to 500  sq ft/gal
 Coverage @ 
Recommended DFT N/A
 Recommended DFT 
Per Coat N/A
 Dry Time
 At 70ºF and 50% 
Relative Humidity 8 hour